• Follow Me

  • Enter your email address to subscribe to this blog and receive notifications of new posts by email.

    Join 2 other followers

  • Google Friend Connect

  • Like Freckles Crafts on Facebook

  • Advertisements

“Countdown to Break” Blocks- Teachers Gift Tutorial

I have been thinking a lot about what to get my son’s teachers for Christmas.  I usually try to get them a gift certificate for Target or Wal-Mart so they may buy books for their classroom or purchase something personal for themselves (they deserve it after all on what little teachers make these days, yeesh!)  With the gift certificate I like to give them something homemade either from myself or the kids.  After being inspired by the many tutorials I have seen recently for countdown to Christmas advent blocks, I came up with this version for teachers to count down the days until their next break.  I think this will be such a fun gift that they can use in the classroom to not only assist with learning the calendar days but to also build excitement counting down the days until spring break, summer break, etc!

What gift are you giving teachers this year?


  • 2- 4 inch wood blocks cut from a 4×4 fence post
  • 1-  2×4 block 7 inches long
  • White paint
  • Paint brush
  • Sandpaper
  • Coordinating scrapbook paper
  • Paper trimmer or scissors
  • Modge Podge
  • Corner trimmer (optional)
  • Vinyl lettering cut to say “days ‘til break”
  • Vinyl numbers: 0, 1, 2, 3, 4, 5 (block one) 0, 1, 2, 6, 7, 8 (block 2)
  • Distressing ink optional


  1.  Sand edges of blocks to remove rough areas.
  2. Paint all sides of each block white as well as the 2×4 base and allow to dry.
  3. Cut scrapbook paper to fit blocks.  You will need six different pieces of paper for each of the block sides and one coordinating piece of paper for one side of the 2×4 (use a corner trimmer to round edges of paper, optional).

4.   Apply scrapbook paper to blocks using a thin layer of modge podge and allow to dry.

5.  Lightly sand the edges of the paper to make it look worn and even with the blocks.  As an option you can use distressing ink on the edges of the paper to give the blocks a worn/aged look.  Note:  I did not do this step because I liked the contrast of the white block with the colorful paper. 

6.  Remove the vinyl scrap from around the letters and numbers.

7.  Apply the vinyl numbers to blocks (0, 1, 2, 3, 4, 5 on block one)(0, 1, 2, 6, 7, 8 on block 2) and the letters (days ’til break) to the 2×4 base using your vinyl transfer tape (follow the manufactures directions for your specific transfer tape product). 

8.  Seal the blocks with another layer of modge podge and allow to dry.

Teachers will love these!


Autumn Craft- 2×4 Thankful Blocks

Recently a friend had her basement redone and had a bunch of 2×4 scrap pieces left over from that project. Of course when I see something that I might be able to use for a craft project I just can’t pass it up.  Much to my husbands dismay, I loaded up the entire back of my truck and brought home as many of those lumber scraps as I could carry! Here is the first project I made.

Wouldn’t this look cute on your fireplace mantle or table at Thanksgiving?  Below are the directions to make your own!

Supplies Needed:
 4- 2×4 boards cut into the following lengths 10.5 in., 5 in., 4 in., 3 in.
Coordinating pieces of Scrapbook paper (DCWV The Green Stack used here)
Distressing ink (optional)
Modge Podge
Paint brush
Paint (Coffee Bean by Plaid used in this project)
Scissors or paper trimmer
Vinyl lettering cut into words “Faith”, “Family”, “Friends” and “We Give Thanks”
Vinyl transfer tape
Corner trimmer (optional)

Sand the block edges to remove rough areas.  Paint the blocks brown and allow to dry.

Cut scrapbook paper to fit the blocks.  Trim the paper slightly smaller than the wood (use corner trimmer to round edges of paper, optional).

Apply scrapbook paper to blocks using a thin layer of Modge Podge and allow to dry.  Lightly sand the ends of the paper to make it look worn and even with the blocks.

Use the distressing ink on the paper to give it an antique look (optional).

Now it is time for the fun part!  Adding the vinyl letters!  Separate the vinyl letters from the backing.

Apply the vinyl lettering to blocks using the vinyl transfer tape (follow manufactures directions for your vinyl transfer tape.)

Seal the blocks with another thin coat of Modge Podge, allow to dry and your project is complete! 

Let’s get one more look at the finished project!  So cute!

%d bloggers like this: